The safety of the items placed there, and sometimes the well-being and health of the owners, depends on how well ventilation works in the cellar. To create a properly functioning air exchange system, an understanding of certain physical processes and knowledge of the device’s technology are required.
We will tell you how to organize an exhaust air system from underground rooms and ensure the supply of fresh portion from the street. The article presented for acquaintance describes in detail the proven options and implementation methods. Based on our recommendations, you can perfectly equip the cellar.
The task of ventilation underground
Cellars are used for long-term storage of items with special environmental requirements. The temperature in the rooms closed underground is almost always kept in the range from +5 to + 12 degrees Celsius.
Moisture values can vary significantly depending, as a rule, on external conditions. Using ventilation, it is possible to adjust these parameters to the required values.
Image Gallery
Photo from
The cellar, a room for storing blanks and long-stored products, is arranged in the socles and basements of houses, separate buildings, in the lower tiers of garages. All options need ventilation
For the formation of normal air exchange in a room partially or completely buried in the ground, it is necessary to ensure the flow of air
For the outflow of air entering the basement or cellar, a device for the exhaust duct or hole is required. Their volume should provide a complete exhaustion of the air entering through the inlet
By the type of motivation for air movement, the ventilation systems for cellars are divided into natural and forced. In vivo, air mass moves according to the laws of gravity; in forced airflow, fans stimulate
Perfectly functioning ventilation will remove excess moisture from the cellar or basement, prevent the appearance of mold, fungus and their consequence - the destruction of structures
The ventilation system is needed to remove stagnant air and accumulating toxins that can create a threat even with a short visit to the basement
Regular ventilation of basements and free-standing cellars will prevent condensation, which spoils food and workpieces
The ventilation system will prevent the accumulation of explosive and toxic substances that accumulate in closed rooms without stable air exchange
Cellar ventilation in the basement of the house
Inlet to basement or cellar
Exhaust ventilation duct of the air exchange system
Forced ventilation units
Extension of the service of building structures
Ventilation for optimal microclimate
Condensation
Exhaust duct
Compliance with the temperature regime
The temperature regime of a properly constructed and insulated cellar is formed due to heat transfer between the walls, the floor and the air inside it. The ceiling, as a rule, is insulated, so its effect on the temperature change inside the structure is minimal.
Seasonal fluctuations in soil temperature are much less than atmospheric, which makes it possible to establish a constant microclimate in the room. Heating or cooling of air inside the cellar is slow due to the low thermal conductivity of the earth.
The classical structure of the cellar provides for heat exchange between the air in it and the earth, which makes up the floor and walls of the room. The influence of atmospheric temperature is eliminated by using a heater
If necessary, ventilation can be used to change the temperature. Given that the structure is underground, the natural movement of air is sufficient for cooling the cellar in winter, while in the summer it is better to stimulate air flow with the help of fans.
Solving the problem of excess moisture
The most common microclimate problem in the cellar is excessive moisture. Evaporation of it using solar radiation or wind exposure is impossible, therefore ventilation is the main way to drain rooms buried in the ground.
Modes of moisture can be divided into three types:
- Moisture can get into the cellar in the form of water through walls, floor or ceiling in the absence or violation of the waterproofing layer. Most often this occurs in the spring during snowmelt.
- The internal source of moisture may be objects or products located indoors. Vegetables and fruits, especially in the initial stage of the storage process, emit fumes. Also, air humidification occurs during the fermentation process, during the breathing of bees, if the cellar is used as an omshanyk and in many other cases.
- In the spring-autumn period, when the temperature in the cellar is much lower than the street temperature, condensate is a source of moisture. Therefore, the proper use of ventilation requires knowledge of the physical laws of condensation and evaporation.
The process of removing moisture through ventilation is slow. Therefore, before starting this procedure, it is necessary to determine the cause of the increase in the humidity of the cellar and, if possible, eliminate it.
Moisture evaporation during ventilation is slow, so if the cause of the appearance of water in the cellar is not eliminated, the drying procedure will have no effect
Reducing the concentration of hazardous gases
Another reason for ventilation is the need to change the chemical composition of the air. So, as a result of the storage of agricultural products, all kinds of smells are released, and when it decays, as well as when bees or fermentation tanks are kept in the cellar, carbon dioxide is liberated, replacing oxygen.
In poorly ventilated cellars, the accumulation of gases of a different nature of origin is possible. Excessive concentration of carbon dioxide (CO2), methane, carbon monoxide (CO) or hydrogen sulfide can cause a person to lack oxygen in the blood, suffocation and, as a result, loss of consciousness. Failure to provide immediate assistance may result in death.
In the absence of internal air circulation, the concentration of hazardous heavy gases occurs at the lower point of the cellar. Therefore, if simple ventilation is sufficient to remove odors, then to reduce the concentration of gases, whose specific gravity with respect to atmospheric air is more than unity, ventilation is necessary with the location of the air inlet at a small distance from the floor.
If there are preconditions for excessive concentration of heavy gases in the cellar, it is necessary either to ventilate the room before visiting it, or use sensors or gas analyzers to determine the need for ventilation.
The process of alcoholic fermentation leads to the active release of carbon dioxide. Due to the need to maintain a constant external temperature, fermentation tanks are often placed in the cellars. In the absence of proper ventilation, sometimes this leads to suffocation of the cellar owners.
Theoretical basis for moisture removal
In that case, if the main goal of air exchange is to dry the room, then from the standpoint of physics the problem can be formulated as follows: it is necessary to perform a ventilation device in the cellar in such a way that the absolute mass of moisture entering the interior is less than the outside.
Physical Description of Condensation and Evaporation
There are three main terms, the essence of which must be clarified in order to understand the nature of condensation and evaporation of moisture from air:
- Absolute humidity shows the mass of water vapor contained in one cubic meter of air. This value is expressed in g / m3.
- Relative humidity shows the ratio of the current mass of water vapor to the maximum possible, at constant pressure and temperature. It is expressed as a percentage.
- The dew point temperature indicates the temperature at which the water vapor contained in the air reaches saturation and the condensation process begins.
In relation to the cellar, the condensation process can be described as follows. At a certain temperature, air has some values of absolute and relative humidity.
With decreasing temperature, the absolute humidity value remains unchanged, and the relative humidity increases. When the relative humidity reaches 100%, the dew point occurs and the discharge of moisture in the form of condensate begins.
The lower the air temperature, the less moisture it can hold in suspension when fully saturated
The evaporation process is as follows: when air in which the relative humidity is less than 100% comes in contact with water, it is saturated with moisture, which can continue until the relative humidity reaches 100%. The higher the air temperature, the greater the amount of moisture it can absorb during evaporation.
Drainage in summer
In dry and hot weather, it is tempting to open a moist cellar for a while and run warm, dry air there to remove condensate. This is one of the most common mistakes leading to the opposite effect - the entry of moisture from the atmosphere into the dungeon.
For example, during the day, with an anticyclone and an air temperature reading of +32 degrees Celsius and a relative humidity of 40%, there is a feeling of air dryness. In the cellar with a temperature of +12 degrees and a relative humidity of 100% there is a feeling of dampness. However, the absolute humidity on the street with these parameters will be greater than indoors.
When ingested, warm air will begin to cool. The dew point temperature at the above street air parameters will be 16 degrees. Consequently, during the period of lowering the temperature from 16 degrees to 12, moisture will condense, and the relative humidity will be 100%.
Besides the fact that the air humidity in the cellar will remain at the same maximum level, there will be an additional flow of water due to condensation
Drainage of underground rooms due to ventilation is correct for a long time. At the same time, the volume of air passing through the premises should provide minimum indicators of temperature drop, so that an evaporation process occurs at low values of its relative humidity.
However, after the end of the ventilation period due to heat exchange with the walls and floor, a gradual decrease in temperature and condensation of water in the air will occur.
Therefore, temporary removal of moisture using ventilation in the warm season is carried out in the following cases:
- the amount of moisture in the cellar clearly exceeds the amount that will be there after condensation of water from atmospheric air;
- it is necessary to create conditions for the cessation of intensive processes of decay, the spread of mold and fungus;
- it is necessary to carry out antifungal treatment, which is most effective when applying an antiseptic to dry surfaces.
Condensate removal from the cellar in the warm season is carried out by alternative methods. Moisture collection can be used with substances that have good hygroscopic (water-absorbing) properties, such as ash or sawdust.
In this case, if possible, it is necessary to exclude external air exchange, if this does not contradict the observance of other parameters of the microclimate of the room.
Drops of condensation from the ceiling are easiest to collect with a dry cloth. In the summer, this is the most effective way to deal with damp in the cellar.
Freezing moisture in winter
At low temperatures, the absolute humidity is small. Therefore, the most effective method of removing dampness through ventilation, which is not quite correctly called “freezing,” is to provide an influx of frosty air into the cellar.
So, even if at a temperature of -10 degrees Celsius the air has the highest possible humidity (2.36 g / cubic meter), then after it is heated in the room to +5 degrees, the value of relative humidity will become only 30%. One cubic meter of such air will be able to evaporate 4.5 grams of water in the cellar.
Since for almost any cellar it is undesirable to lower the temperature to negative values, the intake of frosty air must be carried out in small portions.
It displaces moist air from the room and mixes with the rest. Then you need to wait until the temperature rises to normal values and you can carry out this procedure again.
When draining the cellar using frosty air, it is important to prevent the temperature from dropping below zero for a long time. The effect of cold on vegetables is no less harmful than excessive moisture
This method is effectively used in the fall after planting, opening the ventilation for some time at night.
Technical aspects of the ventilation device
Technically correct implementation of the ventilation system for the cellar, along with an understanding of the rules for its use, will ensure the necessary microclimate in the room. For small structures, you can do all the work yourself, having basic skills in the field of construction.
Image Gallery
Photo from
Ventilation device under construction
Drilling additional vents
Supply fan
Exhaust fan
You can familiarize yourself with the features of calculating the ventilation system for various types of rooms by reading the recommended article.
Air duct placement and maintenance
As ducts usually use plastic or metal pipes. Plastic is required to be resistant to low temperatures. This is necessary in order to avoid breaking it in the winter under mechanical stresses, such as clearing from a chicken.
Usually, two pipes are used for the ventilation of underground rooms, one of which works for air supply, and the second for exhaust. The use of a single pipe results in a much smaller volume of circulating air.
It is advisable to place the exit points of the pipes at different ends of the cellar. In this case, there is uniform ventilation of the entire area of the room, without the formation of zones of stagnation of air.
Image Gallery
Photo from
Metal duct ventilation duct
Accessories for assembling the ventilation system
Duct Mounting Methods
Installing a chimney on a wall
The inlet of the supply ventilation is usually located near the floor of the room, and the place of air intake is closer to the ceiling. This is necessary to comply with the physical laws of the functioning of natural air circulation. An exception is the placement of the entrance to the exhaust pipe near the floor for a more efficient outflow of hazardous heavy gases.
When placing external exits near the ground, it is necessary to monitor the level of snow, since the formation of a snowdrift above the level of the pipe can cause the ventilation to stop.Humid air leaving the room causes a muzzle to form in the chimney, which can reduce the speed of air movement or even cause the ventilation to stop.
Air exchange scheme with correct and incorrect placement in the pipe plan. In the case of complex cellar geometry, it may be necessary to use several points of air inflow or exhaust
Clearing the chicken is sometimes a difficult task due to the content of ice or high density deposits in it. To simplify the work, in autumn, a rigid metal rod with a diameter of 8-12 mm can be inserted inside the pipe. In the case of complete closure of the pipe section by the kurzh, translational movements and rotation of the rod, you can begin the procedure for cleaning the hood.
If the exhaust pipe is located vertically, then under its end, located in the cellar, it is necessary to put a container into which condensate and fragments of snow and ice will fall, crumbling when the pipe is cleaned.
The potato is wet under the chimney due to condensation getting on it. To avoid this, it is necessary to place a container under the opening of the pipe into which water will collect
Natural and forced air circulation
In the vast majority of cases, the natural ventilation of small underground rooms is used. In winter, the physics of the process of air mass circulation is based on the density difference between cold and warm air. To do this, the outlet from the supply pipe is placed closer to the floor, and the entrance to the exhaust pipe is located under the ceiling.
The cross-sectional area of the ducts is calculated on the basis of the necessary indicator of the volume of air circulation and the estimated speed of its movement through the pipes.
To adjust the amount of ventilation, it is better to use a pipe section slightly larger than the design complete with a valve. It can be installed on both the supply and exhaust pipes.
A method known from ancient times with a burning candle located under a chimney. Hot air rises, greatly increasing traction
Natural ventilation does not work well in the summer, and also removes gases for a long time, with a specific gravity greater than that of ordinary air. In this case, to create an air pressure, a forced type of ventilation is constructed by installing axial fans.
You can install fans on both the exhaust and the supply pipe, as well as both at once. With high humidity in the cellar, it is recommended not to install the fan on the exhaust pipe due to its possible rapid breakdown as a result of exposure to moisture.
Moisture removal using condensation zones
There is a way to remove moisture from the cellar in winter, which does not require pipes and openings for the inflow and outflow of air. It consists in the formation of zones for moisture condensation with its subsequent removal. This method does not apply to ventilation, but to circulation, since there is no air exchange between the room and the atmosphere.
The most elementary implementation of this method is to use a canopy outside the ajar cellar door. Warm air, penetrating from the cellar through a small hole, is cooled in contact with the cold canopy, on which condensate remains in the form of hoarfrost and chicken. Cold, dry air returns to the room.
Using a canopy scheme avoids laying ductwork from the cellar to the outside. However, such a system is not automatic - it is necessary to periodically remove the chicken
When applying this method, it will periodically be necessary to move the canopy, close the door, knock down the kurzh and remove it outside. As a canopy, you must use a dense rag that can withstand the weight of up to 20 kg of adhering snow per 1 square meter of its area.
The following article will introduce the rules and technologies for constructing ventilation systems.
Video # 1. The problem of moisture condensation in summer and methods for its elimination:
Video # 2. Assembly and installation of the fan on the exhaust pipe:
For high-quality operation of the ventilation system, it is necessary to carefully approach the issue of studying the physical fundamentals of air circulation, as well as its condensation and evaporation. The technological device for air exchange is not complicated and for small rooms its implementation is possible on its own.
Please comment on the information provided by us. You can leave a comment, ask a question and post pictures on the topic in the block below. Perhaps you want to talk about personal experience in the design of a ventilation system?