Regardless of the type of fuel, a chimney is a mandatory part of the heating system. It depends on his competent device, it will be so warm in the house.
A special type of fuel is gas, because it is unsafe, so many people are concerned about the question: is a deflector in the chimney of a gas boiler necessary and will such a solution be correct? Let's try to deal with this difficult issue in our material.
Popular types of traction amplifiers
In modern design, there are different types of deflectors, so you can choose a model for a house made in any architectural style.
Structurally, these devices differ:
- flat top;
- two ramps;
- semicircular lid;
- folding top.
Each of them has certain advantages: the opening cover on the deflector allows you to control the process of removal of combustion products.
As a decorative element for a roof made in the Art Nouveau style, a flat top is perfect, the best protection against atmospheric influences is a gable mini-roof. As a material for their manufacture, galvanized metal is mainly used, but sometimes it is covered with a layer of plastic or enameled.
What is a deflector?
Strong winds can disrupt the stable operation of the gas boiler. In such conditions, automation is often triggered and the boiler shuts down. Combustion products from a gas boiler with their inefficient removal pose a threat not only to health, but also to people's lives.
To enhance traction by optimizing air flow, traction stabilizers or deflectors are used. In translation, its name sounds like a reflector, a deflecting device. In his work, the Bernoulli effect was applied, based on a decrease in pressure during airflow around an obstacle. It deflects the air masses, increasing the strength of the main chimney stream.
The chimney of a gas boiler equipped with a baffle will not fade with strong gusts of wind. The design becomes more efficient because traction force increases up to 20%
The traction booster works effectively with any wind force and even during strong gusts, if present, the traction will not overturn. But with complete calm, this aerodynamic device acts as an umbrella and is practically inactive, and sometimes reduces traction. For this reason, many experts do not recommend installing baffles on gas flues.
Despite the increased requirements for a deflector installed in the chimney of a gas boiler, in some cases this is the only solution to the problem. If this device is not included in the project, it is necessary to coordinate its installation with gas companies. Only by fulfilling this condition, you can proceed with the installation of the deflector.
According to the specifics of the device and associated with this principle of action, the deflectors are divided into the following varieties:
Image Gallery
Photo from
Traditional umbrella deflector
H-shaped deflector devices
Sail wind deflector
Spark Arrester Model
Deflector Design
The deflector prevents direct air flow into the chimney.
As standard, it consists of 3 parts:
- Top cylinder (diffuser) expanded below. It is attached to the bottom using special racks.
- Bottom glass from metal, ceramics or asbestos cement.
- Cap in the form of a cone-shaped umbrella.
The upper part and the lower cylinder are equipped with annular rebounds deflecting the air flow. In some models, the top element is missing. Then the lower cylinder is installed on the pipe, then the diffuser and the caps - direct and reverse.
The device works according to a simple principle:
- the walls of the cylinder located above take a wind blow and direct the air flow around;
- due to the slip on the surface of individual air jets and their rise upward, there is a suction of gases coming from the chimney.
The thrust is amplified in any direction of the wind, except horizontal. In the latter case, air vortices are formed inside the device, cutting off the smoke exit paths. This significant drawback is eliminated by adding an additional element - the inverse cone.
Structurally, the deflector consists of a diffuser (2) with a frame (3) mounted on the pipe (1). These elements are located in the shell (4). Above the diffuser is an umbrella (5) with thermal insulation (6) and a shield (7). The replacement filter (10) is mounted on supports (9) and secured with bolts (11)
The return cone is installed below the cap. The deflector's task is to ensure that air flows are brought out by crushing them.
Characteristics of popular models
Deflector models differ in both size and wind sensitivity. The most popular models are TsAGI, Khanzhenkov, Volpert-Grigorovich, Smoke Tooth, Hood, aka Sachet, Shenard. The first of these models - developed at the Aerodynamic Institute. Zhukovsky.
More often TsAGI is used in ventilation systems due to the difficulties encountered when cleaning soot. The second model is essentially the same TsAGI, but somewhat improved by the inventor. In fact, this is an additional cylinder around the pipe with an umbrella cover immersed in the cylinder at a certain distance.
TsAGI deflector homeowners choose most often. It has a cylindrical shape. A device is made of galvanized or stainless steel
The Volpert-Grigorovich deflector has established itself as a traction amplifier in chimneys. It works effectively in areas with prevailing lower winds. The design includes 2 cylinders - the lower one with two outlet pipes and the upper one with a cover.
"Smoke tooth" is mounted in a door specially provided in the chimney. Due to the fact that the design includes 2 handles, you can adjust the flow of air.
Covers for smokers make the most different shapes. Sometimes they are coated with heat-resistant enamel. Individual items look very decorative
The Hood deflector has a swivel design. It consists of a semicircular gutter-shaped air trap mounted on a rotary rod mounted inside the pipe. The increase in traction power through the installation of a deflector-vane occurs due to the turbulence that occurs when the wind load.
How to calculate a static deflector?
With the independent manufacture of the deflector, it is necessary to perform calculations and sketch a sketch of the future product. It is necessary to proceed from the inner diameter of the chimney.
The photo shows the dependence of the dimensions of the deflector on the diameter of the chimney. To determine the lower diameter of the diffuser, the basic parameter is multiplied by 2, the upper - by 1.5, the height of the diffuser - also by 1.5, the height of the cone, including the inverse, the height of the umbrella — by 0.25, the pipe entry into the diffuser - by 0.15
For a standard device, the parameters can be selected according to the table:
Pipe inner diameter (cm) | Deflector Height (cm) | Diffuser Diameter (cm) |
12 | 14,4 | 24 |
14 | 16,8 | 28 |
20 | 24 | 40 |
40 | 48 | 80 |
50 | 60 | 100 |
The table will allow you to choose the dimensions of the deflector without performing calculations. But if there are no suitable sizes in it, you still have to arm yourself with a calculator or find the appropriate program on the Internet.
In the manufacture of the deflector with individual parameters, these special formulas are also used to determine the dimensions:
• D diffuser = 1.2 x dvn. pipes;
• H = 1.6 x dvn. pipes;
• Cover width = 1.7 x dvn. pipes.
Having learned all the sizes, you can calculate the sweep of the umbrella cone. If the diameter and height are known, then the diameter of the round billet can be easily calculated using the Pythagorean theorem:
R = √ (D / 2) ² + H²
Now it is necessary to determine the parameters of the sector, which will subsequently be cut from the workpiece.
The full circle length of 360⁰ L is equal to 2π R. The length of the circle underlying the finished cone Lm will be less than L. The length of the arc of the segment (X) is determined from the difference of these lengths. To do this, make up the proportion:
L / 360⁰ = Lm / X
The desired size is calculated from it: X = 360 x Lm / L. The obtained value of X is subtracted from 360⁰ - this will be the size of the cut sector.
So, if the height of the deflector should be equal to 168 mm, and the diameter is 280 mm, then the radius of the workpiece is 219 mm, and its circumference is Lm = 218.7 x 2 x 3.14 = 1373 mm. The desired cone will have a circumference of 280 x 3.14 = 879 mm. Hence, 879/1373 x 360⁰ = 230⁰. The cut sector must have an angle of 360 - 230 = 130⁰.
When it is necessary to cut a workpiece in the form of a truncated cone, it is necessary to solve a more complex problem, because the known value will be the height of the truncated part, and not the cone completely. Regardless of this, the calculation is performed on the basis of the same Pythagorean theorem. The full height is found from the proportion:
(D - Dm) / 2H = D / 2Hp
This implies that Hp = D x H / (D-Dm). Having learned this value, calculate the parameters of the workpiece for a full cone and subtract the upper part from it.
With known parameters: the height of the cone - full or truncated and the radius of the base, by simple calculations, simply determine the radius of the external and internal (in the case of a truncated cone) and then the initial angle and the length of the generating curve
Suppose a truncated cone is required, in which H = 240 mm, the diameter at the base is 400 mm, and the upper circle should have a diameter of 300 mm.
- Full height Hp = 400 x 240 / (400 - 300) = 960 mm.
- The external radius of the workpiece is Rz = √ (400/2) ² + 960² = 980.6 mm.
- The radius of the smaller hole is Rm = √ (960 - 240) ² + (300 | 2) ² = 239 mm.
- Sector angle: 360/2 x 400 / 980.6 = 73.4⁰.
It remains to draw one arc with a radius of 980.6 mm and the second with a radius of 239 mm from the same point and draw radii at an angle of 73.4 °. If you plan to overlap the edges, add allowances.
And more on how to build a deflector on a chimney yourself, read on.
Self assembly device
First, patterns are prepared, then they are laid out on a sheet of metal and parts are cut using special scissors. The body is rolled up, the edges are fastened with rivets. Next, the upper and lower cones are fastened together, using the edge of the first because it is larger and in it you can cut out in several places special mounting cuts with a width of about 1.5 cm, and then bend them.
It is not difficult to assemble a simple deflector, but if a rotary device is to be installed, you will have to deal with many details
Before assembly, 3 racks are installed in the lower cone, evenly distributing them around the perimeter and using threaded rods for this. To connect the umbrella to the diffuser, loops from metal strips are riveted on the latter. The racks are screwed into the hinges and, for greater reliability, are fixed with nuts.
Next, they perform installation work on a deflector made by hand on a chimney of a gas or other type of boiler. The assembled device is placed on the pipe and secured using clamps, avoiding gaps. Sometimes the joint is treated with heat-resistant sealant.
Assembling a simple poppet model
The simplest project to implement is the manufacture of a plate model of the deflector. Such a cap for the chimney can easily be done with your own hands. Its geometric parameters depend on the diameter of the pipe:
Image Gallery
Photo from
Round pipe baffle design
Clamp diameter for mounting the deflector
Chimney Cap Size
The distance between the umbrella and the mounting clamp
In order not to make a mistake in manufacturing and precisely fit the parts to the required size, it is advisable to first make a model of the deflector from cardboard. At this stage, it is simpler and easier to make adjustments to the design. Cardboard blanks at the same time will serve as original patterns for cutting elements of the future deflector:
Image Gallery
Photo from
Making a pattern of the deflector on the chimney
Assembly of a metal umbrella for the chimney
Remote Rack Device
Fixing the fixing clamp of the deflector
Features of mounting a rotary deflector
Turbo deflector, rotary deflector, rotary turbine, Turbovent - all these names refer to one type of mechanical device for enhancing traction. It consists of a static part connected to the chimney and an active head with blades in the form of a ball.
A rotary baffle is the only device that is not recommended to be mounted on chimneys of stoves heated with solid fuel and wood-burning fireplaces. Turbovent has a characteristic feature - to bleed air from a pipe even during that period when heating does not work.
The direction of rotation of this nozzle does not depend on either the force or the direction of the wind. It occurs only in one constant direction, creating the effect of an incomplete vacuum. As a result of this, the thrust power increases under conditions of rarefaction of air, and the risk of tipping over the thrust is practically equal to 0.
In the chimneys of gas boilers, Turbovent does its job well and can serve as an ornament for any facade. If you compare it with other types of deflectors, then in efficiency it exceeds them by 2 times.
The base of the rotary deflector can be round, square, flat square. Head sizes range from 100 - 680 mm. Its service life is up to 15 years.
With all the advantages of a rotational turbine, there is one, but a significant drawback - in the calm mode, the device stops. If precipitation occurs at this time at temperatures below 0, then the head may freeze and will have to take measures to start it.
Despite the relative complexity of the design, installing a rotary deflector is not difficult. The device has a small weight, so for the installation of enough effort by one person and time of about 2 hours. A suitable place is the highest point of the roof. This arrangement will not allow snow to fall into the pipe if there is an accumulation of precipitation around it.
The movement of the head of the rotary turbine is carried out using bearings. The device operates autonomously and very effectively copes with the task of venting gases, but in calm weather it is useless
For different models of rotary turbines, there is one requirement: the temperature of the combustion products above the pipe should not exceed 150-250⁰. The dimensions of the base must be precisely matched to the chimney. The turbocharged deflector must meet the characteristics of the boiler, and this point must be considered when choosing a device.
There are turbo deflectors from different brands on the market. Among the most reputable are Turbovent, Turbomax, Rotowent. The first manufacturer produces products with a base of various geometries.
You can identify them by marking TA-315, TA-355, TA-500. In it, the figure indicates the diameter in the case of a circular cross section or the dimensions of a rectangular base.
Deflector Turbomax produces a Belarusian company. They make devices from high-quality material - stainless steel from a European supplier. Rotowent also made of stainless steel, supplied from Poland. Looks harmoniously on the roof of any type. Suitable for both a chimney and ventilation pipes. Withstands a large operating temperature - about 500⁰.
Chimney baffles
Structurally, the chimney weather vane is designed so that the gases, leaving freely on the leeward side, increase the traction force in the chimney. A device made of heat-resistant steel is well established in conditions of high temperatures and the formation of condensate.
Under the curved visor of the fly-gun there is a bearing assembly, which insures against problems with rotation.The bearing assembly is bolted to the chimney. The rarefaction zone is created when the air stream passes through the space under the visors.
During installation, the base of the device is put on a round chimney until it stops, and then fixed with 3 bolts. Tighten the bolts with great care since damage to the pipe. Installation is completed by checking the verticality and rotation of the housing
The minus of chimney weathercocks is that when the wind is strong, they work unstably. The moving part must be periodically cleaned and lubricated. Moisture often accumulates inside the device, and flue gases leave a trail in the form of deposits.
Manufacturers themselves advise using their devices if the chimney is in an unfavorable location. It, in fact, does not increase traction, but only protects the chimney.
There are a lot of designs of deflectors, but we must not forget that gas is used for heating. Not all models can be used. Some of them are not suitable in principle because designed for ventilation. In order not to block the smoke removal system, you must always consult with a specialist and get permission to install a baffle.
Looking for a chimney deflector? Or is there experience in manufacturing or installing this device? Please share it with visitors to our site. Also, in the block with comments, you can ask questions of interest to the topic of the article.