The quality of a home sewer system should not be inferior in terms of reliability to a water supply system or electric network. If the sewage system in the apartment is assembled with high quality, it will last for more than a dozen years, provided that the installation standards and the use of high-quality consumables are observed.
You doubt your strength and are afraid to make mistakes? We will help you to correctly design and install a sewer system. The main thing is to take into account all the basic requirements, choose the right pipes and adhere to the installation technology described in the article.
How to equip the sewer in the apartment?
Before you pick up pipes and everything you need, before starting work, you need to understand the principles of the functioning of the sewer system, including observing the angle of inclination, so that the pressure in the riser is slightly higher than atmospheric.
Otherwise, atmospheric air will squeeze unpleasant sewer gases directly into the apartment. If the internal pressure is too high, the waste gases can eject drains from siphons.
Let us consider more closely all the nuances of the sewage system in the apartment.
Slope pipes - an important condition for the functioning of the system
When laying the trunk, you must observe the horizontal angle, which must be within certain limits. The insufficient slope of the sewer pipes will not allow the drains to drain normally into the riser. If the slope is too large, the water will drain quickly, leaving contamination on the pipe walls.
Observe the slope to achieve optimal fluidity in the sewer and the correct pressure in the pipes. Pipe slope standards must comply with SNiP (+)
The paradox is that with high "fluidity" the sewage system will become clogged.
The dependence of the slope of the laying of the pipeline on the cross section of the highway:
- 30 mm / m at 50 mm;
- 20 mm / m at 110 mm;
- 8 mm / m at 160 mm;
- 7 mm / m at 200 mm.
Thus, the maximum slope should be within 150 mm / m. Exceptions are bends up to 1.5 m long for some plumbing fixtures, such as a toilet.
Sewer pipes can be connected at right angles only in a vertical orientation according to the principle of a waterfall.
Image Gallery
Photo from
Sewer pipe slope
Direction of slope of sewer pipes
Marking the sewer line in front of the device
Finish fixing sewer pipes
Friendship with neighbors is half the success
For the replacement of the internal sewage system in the apartment to be successful and with minimal hassle, good relations with neighbors from above are needed. They should refrain from using sewage during installation. To be more safe, it is better to turn off the cold and hot water riser in the basement.
Based on this, all work should be carried out expeditiously, preferably on a weekday during the daytime, when most of the tenants at home are at work.
Work Precautions
Sometimes a warning about the inadmissibility of the use of sewage by neighbors may be ignored by some residents.
Take care of safety measures when performing work, because dismantling and replacing sewer equipment is a high-risk event
You need to be prepared for an emergency situation and use the following protective measures:
- stick the walls and the floor with tape, fastening all joints with tape;
- prepare a bathroom - clean the room and dismantle the toilet;
- use protective equipment - raincoat, hard hat with glass, rubber boots.
A helmet is necessary, because you will have to work with a heavy cast-iron pipe hanging over your head.
Fixation of the main sewer
The lion's share of success in the reliable installation of sewerage is occupied by the reliably installed upper part of the riser. Do not rely on the remaining mounts, as over time, they become worthless.
The cast iron pipe may burst due to vibrations of the power tool. All this can cause a serious accident for which you will have to pay.
A high-quality mounting unit also acts as a damper, absorbing vibration. A securely secured riser will minimize the likelihood of an accident.
The sequence of actions when fixing the riser:
- mount on both sides of the riser under the ceiling itself two crutches with a diameter of at least 12 mm;
- fixation with a mortar or stud with a metal collet;
- the hairpin should protrude beyond the middle of the pipe by at least 40 mm;
- secure the riser with half clamps.
Under the half-clamps, you need to put tight rubber gaskets (you can from the car camera). Holes are drilled in the eyes of the half-clamps for the installation of studs. Each bracket is attached to the stud with a nut. They must be tightened alternately to prevent lateral forces on the pipe.
The riser must be secure in all places - use strong crutches with studs, clamps and brackets suitable in diameter
You can not attach the riser to the wall using one bracket or only one clamp. If the pipe fits snugly against the wall, then under it you need to hollow out a small groove in order to insert the clamp. Remember that cast iron is very fragile, so you need to be extremely careful.
How to choose pipes?
There is no point in talking about the advantages of plastic pipes over cast-iron pipes, but the former are different in both cost and composition.
Possible options:
- Propylene. Withstands up to + 130 ° C, allows cleaning with a plumbing cable, and the use of active chemicals with the exception of alkalis and acids, has a rough inner surface, which increases hydraulic resistance.
- PVC. An inexpensive option that has the smoothest surfaces. It allows the temperature of effluents to 80 degrees, inferior to propylene in strength and chemical resistance, but has less hydraulic resistance. Cleaning with a plunger or ultrasound is allowed.
- Polyethylene. Cheap and unreliable. It undergoes deformation, is poorly sealed and has low heat resistance.
We choose PVC or propylene, taking into account their technical and operational qualities.
The characteristics of different types of sewer pipes are described in detail in the articles:
- Silent sewage: principles of arrangement + installation examples
- Pipes for sewage in the house: which pipes are best used for the device of the internal sewer network
How to choose a pipe diameter?
The minimum diameter of 32 mm when laying the sewage system is used when the system has separate risers, and also when the common end point of the drain is at a distance of no more than 7 m from the riser. Under any other conditions, you need to choose pipes with a diameter of 40-50 mm.
There are several types of sewer pipes from various manufacturers on the market - pay attention to cross-section, thickness, strength and heat resistance
Regarding the riser, its diameter should be at least 110 mm. In some cases, a pipe of 160 and 200 mm is used. According to the diameter, the corresponding fasteners to the wall are selected.
Example: if in the kitchen there is only one drain (sink), then you can lay a pipe of 35 mm to the bathroom. Already with a bath, the drain must have a diameter of at least 40 mm.
Image Gallery
Photo from
Sink and bath outlet lines
Sewer branch in the kitchen
Toilet drain
Pipe diameter before and after the toilet
The procedure for the installation of sewage
To maximize productivity and efficiency, it is recommended to adhere to the following order:
- We determine the location of all plumbing fixtures if we plan to add new equipment or change the old scheme.
- We draw the whole scheme of sewer wiring with a chalk or pencil. The diagram should indicate the pipe routes, length, diameters and slopes for each section.
- We dismantle the old wiring system.
- We calculate the number of pipes, consumables and fittings, sealant.
- We purchase all the elements, including adapter couplings from a cast-iron riser to a plastic.
- We mount the system in free space, trying on pipes.
- We carry out the dismantling of old equipment.
- We install the pipeline, customize it at the joints.
- We connect the pipes and seal the joints.
- We mount and connect plumbing.
- We connect the system to the riser.
- When the sealant hardens, we check the system for leaks.
Now, at the key stages of work, we will dwell more carefully, finding out some subtleties.
Sewer charting
If the installation of a new sewage system is simply a matter of replacing the pipes in the toilet and bathroom, then you do not need to come up with a new scheme. Everything is done exactly as it was. But if there were problems with the old sewer system and it is planned to add new plumbing, then it is necessary to accurately withstand all diameters and slopes.
Before starting work, think over a detailed diagram of how the finished sewage system will look and what materials you need to purchase for this (+)
To make sure that the drawn up sewage scheme in the apartment is correct, it is better to give it to specialists for verification. This is significantly cheaper than ordering a compilation from scratch.
The following elements should be indicated on the diagram:
- all rooms where the sewer will pass;
- the location of the elements for each room, indicating the distance from the wall, the length of each section, as well as the total length of the pipeline;
- a full range of fittings, including revision and sewage bends;
- the place where the central riser is located.
The scheme should be as detailed as possible so as not to forget anything and not violate the technology.
Image Gallery
Photo from
Sewerage system in the apartment
Sewer riser inspection
Sewer pipe inspection
Pipe cleaning
Removing the old system
It is necessary to analyze the old wiring in order to select the appropriate dismantling method. If the plastic changes, then, as a rule, it is simply pulled out of the joints with simultaneous scrolling.
Sometimes cast-iron pipes can be dismantled in the same way, but at the same time you need to knock out the joints with a chisel.
In all other cases, of which the majority, it is necessary to file a cast-iron pipe with a diamond wheel from different sides. A wedge is inserted into the resulting hole, on which you need to hit several times with a kilogram hammer until the pipe is divided into two parts.
You should start by disconnecting the pipeline from the riser, and direct dismantling is carried out starting from the farthest section of the sewer. It is necessary to warn the neighbors, block the water in the riser and proceed with dismantling.
Use a power tool to make two cuts in a cast-iron pipe for dismantling - in another way it is extremely difficult to detach attached pipes
Disconnect the pipe that adjoins the riser. This is done through two cuts at a distance of 150 mm from each other. First, a fragment of the pipe breaks out from the side of the apartment with a wedge, and then a piece from the riser side.
Next, you need to hammer the old seal near the outlet of the riser with a hammer in order to remove the remaining fragment of the pipe. Holes need to be tightly plugged with rags. Now you can allow your neighbors to use the water supply while you dismantle the rest of the pipeline in the apartment.
Then again we introduce a ban on the use of sewage. Lastly, we cut off the old riser in order to proceed to its replacement.
Sewer riser replacement
This is an extremely responsible task that is best entrusted to seasoned specialists, otherwise the price of an error may be too high.
If you are confident in your abilities, then you will need the following set of tools and supplies:
- two cuff adapters - plastic / cast iron and cast iron / plastic;
- two pipes of appropriate length and diameter;
- two plastic 45-degree turns;
- expansion joint for plastic pipes;
- metal clamps with studs for mounting;
- plastic cross with a branch of 50 mm in the required direction;
- plastic insert with revision hatch.
First you need to strengthen the old riser at the very top. Make two cuts in the middle of the cast-iron pipe in the middle at a distance of 150 mm from each other. In the lower cut, insert two wedges on both sides of the pipe at an angle of 45 ° to the horizontal.
Dismantling the riser should be done by a trained master with sufficient experience in such work, so think carefully before you start this yourself
By tapping it is necessary to achieve chipping of the pipe. This operation requires substantial experience, as if the wrong approach, the entire pipe string could collapse.
Insert the wedges into the upper cut and in the same way release another section of the pipe. At the same time, assistants must always hold the upper part of the pipe. Next, use a chisel to remove the entire old seal at the top.
With small swings, you need to release the pipe from the joint. Now also repeat for the bottom joint, eliminating the termination and taking out the pipe with swaying.
We collect a new riser according to the scheme, start from the top and end with the bottom:
- trumpet;
- adjusting branch;
- compensator;
- revision compartment;
- trumpet;
- crosspiece.
The lower and upper part must be connected to the cast-iron riser using cuffs.
Ensure that all elements are installed in the correct order and that the cuffs are securely tensioned on the pipe surface.
We adjust the dimensions of the lower pipe during the rough assembly process. Then we carry out the final installation using sealant, connect the lower wiring and mount the toilet. We fix the riser with the help of crutches with studs at four points, including each adjustment branch, and also 1/3 of the length from the lower and upper edges.
Material calculation and fitting
It is necessary to calculate the amount of materials so that in the process of work it is necessary to cut pipes as little as possible, these are all additional costs. Pay attention to the length of the sections. In an ideal situation, pruning will only have to be done for one pipe.
After everything you need is on hand, you need to find out a few points with the help of fitting.
Firstly, you need to understand how the couplings will be placed, whether pipe tails will hang on the walls, whether there is enough space for installing the couplings. It is also required to note the location of crutches and determine their number.
Secondly, it is necessary to identify difficult places where installation can be complicated and think through its sequence.
Rough installation of the pipeline
The preliminary connection of pipes is carried out without sealing. The ends of the pipeline are interconnected only by complete nozzles. Next, we cut the pipes from the side of the free end.
It is impossible to cut from the pipe side, as this will violate the design and tightness of the connection in the future.
To verify compliance with the scheme, assemble the entire system from sewer pipes, but do not use sealant yet, adjust all connections
Cutting is performed with a hacksaw for metal strictly at right angles. All burrs must be removed with a knife, including bevels. If this is not done, then the remaining fibers will serve as a clogging site. All rotary splitters must be immediately turned to the operating position.
Fine installation and sealing
Starting with the removal of the riser, we connect the entire system in sections. Special attention must be paid to the reliability of sealing - for this, a pipe sealant is used.
The composition should be neutral - it is better to use polyurethane or silicone. Sealant must be applied to each plastic gasket. Rubber seals do not need to be applied.
It is necessary to lubricate the outer part of the pipe, which will contact when connecting, as well as the inner part of the pipe. We connect each section individually. After the sealant hardens, you need to check the entire system for leaks, letting water into the drain from all plumbing, including the bathroom. In this case, not a drop of water should be on the floor.
Installation of sewage in an apartment is a laborious process, but knowledge of the subtleties will help to make a competent installation. Use the video tips to expand your knowledge and watch the work of professionals.
Now you know how to plan and carry out sewage in the apartment. The process of dismantling and installing equipment is accompanied by many professional nuances, so if necessary, it is better to contact specialists.
Have experience in solving such problems? Or there were questions about the arrangement of sewage in the apartment? Please share your opinion and leave comments. The communication unit is located below.