New developments aimed at saving costs for heating a house are attracting more and more attention. Among the new products and vacuum heating radiators. These are ordinary batteries externally, but completely different in principle.
They are suitable for both a centralized heating system and an autonomous one. In this material we will talk in detail about the principles of operation of vacuum radiators, their varieties, and also dwell on the nuances that you need to keep in mind when choosing heating radiators for the home.
What is a vacuum battery?
A vacuum radiator was called because air was completely pumped out of the internal cavity of this steel sectional structure. This is done in order to reduce pressure.
A liquid substance is placed in hermetically sealed sections, which has the property of easily evaporating at a low temperature. Usually it is either ethanol or lithium bromide liquid.
In fact, the operation of the vacuum battery is based on the principle of functioning of a sealed two-phase thermosiphon. Moreover, it has good heat transfer properties.
A system with such devices is low inertia. It quickly enters the operating mode and almost instantly responds to changes in heat loss.
Radiator | Heat carrier consumption g / s. | Heat carrier temperature ° С | The surface of the heating device in% for 2 minutes | The surface of the heating device in% for 4 minutes |
Cast iron | 50 | 75 | 25 | 40 |
Aluminum | 50 | 75 | 45 | 85 |
Vacuum | 50 | 75 | 70 | 100 |
The table shows the heating efficiency of different radiators. From the surface of the vacuum heating unit, heat transfer to the room begins much faster.
The vacuum battery has an optimal ratio between thermal radiation and convection in the total heat transfer. The first indicator is 80%, the second - 20%.
Types of vacuum radiators
The range of vacuum devices includes products created for electric heating, vacuum registers, panel radiators. You can find on sale and exclusive designer products.
The vacuum electric radiator models deserve special attention, although they are more expensive. This is a good outlet for owners of rarely visited suburban real estate.
Design vacuum radiator in the form of a stand for firewood. You can not only stack logs on it, but also dry them
Instead of a horizontally located channel with a coolant in this device there is a tubular heater type of cartridge type with a capacity of more than 50 W per one section.
This heater transfers heat to the aggregate - oil or water, thereby warming the lithium bromide liquid. When installing such models, grounding is necessary.
The device and principle of operation
The difference between vacuum radiators and bimetallic and aluminum analogues can be seen during their external examination. The former have a greater distance between the sections. This heater consists of a housing, a horizontal channel and vertical sections.
Simplified diagram of a vacuum radiator. Its main elements are the collector (1) and vertical sections (2), in which the secondary coolant is located
The first of these elements includes two sections made of 1.5 mm steel. A horizontal channel is a primary circuit located at the bottom and connected to a heat source. A coolant passes through it, transferring heat to the liquid located in sections that are perpendicular to this channel.
The vertical sections are filled with a secondary coolant - a heat transformer. They are completely isolated from the primary circuit. Their number is directly proportional to the degree of heating of the room. The rate of fluid heating affects the pressure inside the cavities. The larger it is, the lower the pressure.
The secondary coolant is a liquid based on bromine and lithium. In the circuit, it is in a small volume and has the property to boil and quickly evaporate at a small temperature of about 35 ° C.
The circuits have good insulation against each other and the environment.
The process taking place in vacuum batteries looks like this:
- Antifreeze or water heats the horizontal channel.
- Heat from the horizontal channel is sent to the vertical sections.
- The heat transformer boils, causing the steam to fill the entire secondary circuit.
- The walls of the secondary circuit heat up and generate heat into the room.
To ensure efficient transfer of thermal rays from lithium bromide liquid to the walls of the radiator, the state of the working substance should be brought as close as possible to the fog stage. Then the heat will be transported by drops of warm liquid.
To achieve this, the basic condition must be met - the input in the pipes must have a temperature of at least 40 and a maximum of 60 ° C.
Vacuum appliances provide a room temperature of a degree 2-3 degrees lower than traditional batteries. But the cost of heating a house is reduced by an average of 17%
In the case of an autonomous system, achieving such indicators is difficult. In areas of the heating system remote from the source, the coolant will cool off very quickly. The output in the use of pyrolysis boilers with an optimal temperature regime from 45 to 60 ° C or from 50 to 70 ° C.
In another way, the problem is solved by mounting one mixing unit in front of a group of vacuum radiators. In this case, the low-temperature level will ensure the connection of heated water with chilled water from the return. The duty cycle in a vacuum radiator is repeated after the condensate is lowered down the inner walls.
Positive and negative qualities of devices
In favor of the use of radiators that do not contain gases in the cavity, the following arguments are usually given:
- guaranteed absence of such a thing as airing the system;
- low hydraulic resistance;
- complete absence or minimal corrosion;
- stable heat transfer, as dirt does not settle on the inner surface of the case;
- the minimum number of threaded connections, which makes leakage unlikely;
- a wide selection of coolant: antifreeze, water, steam, etc.
If you compare these products and the usual water, then in apartments that are heated centrally, the air will not be heated the same. In the second case, the water entering the system heats the entire radiator body directly. In vacuum, water from the central highway heats only the lower part.
The use of vacuum radiators gives a coolant savings of up to 80%. In addition, when the battery is turned off, heated gas particles slow down, so it cools for a long time
The remaining sections of the battery receive heat from the evaporated liquid. Due to the fact that the heat transformer has both temperature and thermal conductivity lower than that of water, the walls of the vertical sections of the radiator will warm up less.
To ensure the same temperature conditions as in the presence of water batteries, the vacuum radiator should have a large area.
Manufacturers claim that sections of the product warm up instantly. With a small volume of water of 0.5 l, one fragment has a heat transfer of 300 watts. It should be noted that each section, which has become a classic, of a cast-iron radiator contains 4 liters of liquid.
Savings are especially noticeable when using antifreeze. The cost of its acquisition will decrease significantly. A small amount of coolant, the lack of need for expensive equipment are the main advantages of using vacuum radiators.
The advantage of these devices is the fact that the room warms up more smoothly vertically. According to measurements, for each meter of height the difference is about 0.5 ° C. In a room with a ceiling height of 2.5 m between the appliance and the floor, this will be approximately 1.25 ° C.
The effectiveness of vacuum radiators is manifested in the application of alternative energy production resources, such as a heat pump, solar panels.
While cast iron batteries can heat the room when the coolant reaches a temperature of at least 65 ° C, 35 ° C is enough for vacuum appliances
You should be aware that if a section depressurizes due to some circumstances, the vacuum radiator will not work. The reason is that the pressure indicators inside and outside the housing are equal.
Such a breakdown threatens the well-being and health of the people living in the house, because the liquid inside is poisonous.
When is a vacuum radiator beneficial?
Based on the features of a vacuum radiator, we can conclude that its use in a central heating system will not bring special benefits.
Using the appliance is justified when choosing an autonomous heating system. If it is not water that circulates in it, but a non-freezing fluid, then the cost of the coolant will decrease significantly.
A heating system with vacuum radiators is very effective in tandem with a solar collector. For the cottage is the best modern technology
Installation of vacuum batteries is a rational solution to the problem if a low-power boiler is purchased. Such a source will not be able to heat the coolant to the high temperature necessary for the operation of traditional devices. In the case of a vacuum unit, this is not required. The reaction inside it will start already at 35 ° C.
Country cottages, which the owners do not use for living constantly, warm up for a long time in the cold. The vacuum radiator will speed up the process. The process of heating with its participation occurs quickly, and the heat is distributed evenly.
Product Selection Rules
With the popularity of this high-tech equipment on the market, more and more counterfeit of low quality is found.
When buying, you should check whether the device has the appropriate certificates and other technical documentation. It should be remembered that the main rule of effective operation of the unit is complete tightness.
An important parameter for the radiator is also such a parameter as the amount of coolant in the vertical sections - lithium-bromide mixture. Large volumes may cause fluid to flow.
To assess the compliance of the volume, you need to focus on the sound that occurs when the unit sways. It should resemble a soft rustle. If the sound of the flowing liquid is clearly distinguishable, the radiator, with a high degree of probability, can turn out to be a makeshift fake.
For most of their models, European manufacturers give a guarantee of up to 5 years. Their prices are directly proportional to the number of sections and they are higher than for water counterparts
On products manufactured by factory technology, welding seams do not have any flaws, unlike units of unknown origin.
Manufacturers with a good reputation cover product bodies with high-quality powder paint. Therefore, the integrity of the paint layer is difficult to break even in contact with the solvent. You should not miss such a moment as the tightness of the filling valve.
DIY installation details
Installing a vacuum radiator is not difficult, but in order to do without alterations, you need to learn a few rules. It is necessary to observe the recommendations regarding the placement of the unit relative to the wall, floor, window sill.
At the same time, the distance between the radiator and the wall is at least 50 mm, between the device and the floor - from 20 to 50 mm, the optimal distance to the back of the window sill is 50-100 mm.
The photo shows the options for connecting radiators. You should be aware that the inclusion in the heating circuit of other heating devices along with vacuum reduces its effectiveness
The installation itself is not much different from the insert in the system of radiators of other types. The only difference is that the entrance and exit are at the bottom.
Installation of a vacuum unit provides a chain of the following actions:
- The coolant is drained, the old heater is dismantled.
- Mark the installation locations.
- Mount brackets. They are tested for stability, strength.
- Mount ball valves. Through them, the device is connected to the highway. Joints must be sealed using tow or sealant.
- Check the system for leaks.
To improve heat transfer, a foil sheet can be placed on the wall behind the radiator. If you have previously made thermal insulation, you will have to increase the length of the brackets by an amount equal to the thickness of the thermal insulation layer. If the house is insulated, the efficiency of the heating system will increase.
The best manufacturers of vacuum radiators
A wide assortment in the market of heating appliances is not yet different. Among consumers, products of the company enjoy special authority. EnergyEco. This Russian manufacturer uses 1.5 mm steel for the manufacture of batteries. Users note high-quality performance, good heat dissipation - about 170 kW per element.
The working pressure for the radiator is from 0.6 to 1.3 MPa. Even at 2 MPa, the device can work, but 5 MPa is very much for it - it begins to collapse. The cost of the radiator from EnergyEko is considerable, but the demand for it does not fall.
Manufacturer Forevacuum produces vacuum devices of wall and baseboard type. The heat transfer of a register 1 m long at a coolant temperature of 50 ° C is 239 W.
The thermosiphon register is notable for its small metal consumption, i.e. its thin-walled housing is not designed for high internal pressure. At 50 ° C and using ethanol, it is only 0.027 MPa
You can also find Chinese-made radiators on the market. They will have a lower price, but sometimes of dubious quality. When you purchase them, you should carefully inspect, check the documentation.
Acquaintance with the design of the vacuum device and the principle of its operation:
Some craftsmen create vacuum batteries with their own hands:
There are conflicting opinions regarding the advisability of using vacuum radiators. But in some cases, this heating method can be very effective. The main thing is to make sure when buying their excellent quality and complete safety.
Have questions, find bugs or would like to supplement this material with your own opinion about vacuum heating radiators? Please leave your comments in the contact block located under the article.